Scoot Trooper Helmet Limited / Legend Edition
Modérateur : Staff MIB
- polothejedi
- Staff MIB - Admin
- Messages : 22276
- Inscription : 16 janv. 2008 19:43
- Localisation : 69550- AMPLEPUIS
- Contact :
Mais il est sale, et moi je le veux propre !!!! En plus pas que que les coups d'aerographe chinois soit très réussi...
501st Legion Member - TK27388
- RED LEADER
- Original Trilogy Collection
- Messages : 170
- Inscription : 24 avr. 2011 12:39
Ok, c'est bien ce que j'imaginais, le Legend, c'est la version cheap du Limited.dep974 a écrit :ici le legend est en ABS contrairement au limited qui est en FB...donc plus accurate...donc mieux généralement
- turtle74100
- POTF2 - SOTE
- Messages : 4490
- Inscription : 19 juil. 2011 18:30
- Localisation : Haute-Savoie
legend commandé !!!!
Que La Force soit avec toi à tout jamais .........
- polothejedi
- Staff MIB - Admin
- Messages : 22276
- Inscription : 16 janv. 2008 19:43
- Localisation : 69550- AMPLEPUIS
- Contact :
Bien joué les gars !!!! Si vous revendez le blaster, faites signe
501st Legion Member - TK27388
- turtle74100
- POTF2 - SOTE
- Messages : 4490
- Inscription : 19 juil. 2011 18:30
- Localisation : Haute-Savoie
6 plutot
Que La Force soit avec toi à tout jamais .........
- vador28100
- Vintage
- Messages : 27637
- Inscription : 16 mai 2007 17:52
- Localisation : L'Étoile noire
optimiste vaturtle74100 a écrit :6 plutot
cherche photos dédicacé /ma collec : http://www2.mintinbox.net/forum/viewtop ... 14&t=18107
- turtle74100
- POTF2 - SOTE
- Messages : 4490
- Inscription : 19 juil. 2011 18:30
- Localisation : Haute-Savoie
oui oui oui oui oui ce qui revalorise le version legend !!!
moi qui était déçu de l'avoir préco plutôt que le limited ....
Je suis refais
moi qui était déçu de l'avoir préco plutôt que le limited ....
Je suis refais
Que La Force soit avec toi à tout jamais .........
- turtle74100
- POTF2 - SOTE
- Messages : 4490
- Inscription : 19 juil. 2011 18:30
- Localisation : Haute-Savoie
j'ai reçu un mail ce matin de "Bryan" de chez efx , annonçant un petit problème sur la fabrication du casque :
voici le mail :
First, I would like to thank you for your patience on the release of our Biker Scout helmet.
We have run into a manufacturing issue, which is causing this delay. As many of you know, the facemask was never intended to be a feature to be used in the filming of ROTJ. According to Nilos Rodis-Jamero, it was only as a convenience to the actors so that when they wanted to take a break, they did not have to remove their helmets. So, the proper engineering was not necessary to accommodate this feature for the actors.
After extensive reliability testing of opening and closing the face mask many times, the hole begins to become deformed and thus ultimately becomes very loose. This is because the facemask does not lift straight up due to geometry of the sculpt of the facemask and dome, We have established that this is primarily due to the fact that the surfaces are parallel. Thus, the challenge is to resolve this problem, yet not affect the geometry of the original sculpt!
Now that the factory is back from the Chinese New Years holiday and at full capacity, we are working diligently to resolve this issue as quickly as possible. And, we hope to start shipping by comic con.
Thanks once again for your patience and we sincerely apologize for the inconvenience this delay may have caused!
Bryan
DONC normalement en juillet
voici le mail :
First, I would like to thank you for your patience on the release of our Biker Scout helmet.
We have run into a manufacturing issue, which is causing this delay. As many of you know, the facemask was never intended to be a feature to be used in the filming of ROTJ. According to Nilos Rodis-Jamero, it was only as a convenience to the actors so that when they wanted to take a break, they did not have to remove their helmets. So, the proper engineering was not necessary to accommodate this feature for the actors.
After extensive reliability testing of opening and closing the face mask many times, the hole begins to become deformed and thus ultimately becomes very loose. This is because the facemask does not lift straight up due to geometry of the sculpt of the facemask and dome, We have established that this is primarily due to the fact that the surfaces are parallel. Thus, the challenge is to resolve this problem, yet not affect the geometry of the original sculpt!
Now that the factory is back from the Chinese New Years holiday and at full capacity, we are working diligently to resolve this issue as quickly as possible. And, we hope to start shipping by comic con.
Thanks once again for your patience and we sincerely apologize for the inconvenience this delay may have caused!
Bryan
DONC normalement en juillet
Que La Force soit avec toi à tout jamais .........
- polothejedi
- Staff MIB - Admin
- Messages : 22276
- Inscription : 16 janv. 2008 19:43
- Localisation : 69550- AMPLEPUIS
- Contact :
Bizarrement les casques des membres 501st n'ont pas le soucis lol
501st Legion Member - TK27388